ttf4141
(Account not Activated)


Registration Date: 04-14-2019
Date of Birth: Not Specified
Local Time: 04-19-2019 at 05:40 PM
Status: Offline

ttf4141's Forum Info
Joined: 04-14-2019
Last Visit: 04-14-2019, 01:41 AM
Total Posts: 0 (0 posts per day | 0 percent of total posts)
(Find All Posts)
Total Threads: 0 (0 threads per day | 0 percent of total threads)
(Find All Threads)
Time Spent Online: 30 Seconds
Members Referred: 0

ttf4141's Contact Details
Email: Send ttf4141 an email.
  
Additional Info About ttf4141
Bio: It is a relatively advanced conveyor belt repairing equipment at home and abroad. It can be used for the maintenance and repair of damaged fabrics of canvas, nylon core and steel cord; it can also be repaired for special conveyor belts such as heat and corrosion resistance belts.
Introduction
During running of conveyor, due to reasons of heavy material, drop or equipment trouble may lead to spot-shape damage of conveyor belt, then we should repair it immediately. DLCBV-I spot belt repair vulcanizer is specially used to repair small size broken and spot-shape of conveyor belt, it suits for EP, Nylon, Canvas and steel cord belt.
Features & Usage
DLBRV-I spot repair vulcanizer mainly used to repair the small patches of conveyor belts & the belt core layers damaged caused by belt piercing. Namely, to repair the the spot, points defects, DLBRV-I featuring that: simple structure, light weight, easy operation, and it can use the Conveyor belt vulcanizer’s cross beam for the purpose of minimizing the equipment purchase costs, the operation methods is same as the Conveyor belt vulcanizer.
Structure of spot repair vulcanizer
Technical parameter
1. Heating plate size: 350*350 mm;
2. Max. Repair size: 250*250 mm;
3. Working pressure: 0.5--1.0 MPa;
4. Rated power: 2.0 KW;
5. Heating up time< 30 minutes;
6. Timer adjust range: 0-99 minutes;
7. Temperature adjust range: 0-200 ℃;
8. Voltage: 220-660V, 50/60HZ, 3 Phases;
9. Repair belt width: 650 mm--2200 mm.
ModelDLBRV-I
Product nameC Clamp spot belt repair vulcanizer
Type of conveyor beltCanvas, nylon and steel cord belt
Width range(mm)650—1400
Maximum size for belt repairing(mm)250×250
Heating plate size(mm)350×350
Vulcanizing temperature 145℃Adjustable 0—200℃
Total power(Kw)2
Voltage(V)220-660V, 50/60HZ, 3 Phases
Temperature difference of vulcanized heating plates±3
Vulcanization pressure(Mpa)0.5
Warm up time(min)<30
Installation
1. Please move the repair machine to the repair location.
2. Please fill the raw rubber to the broken part. (The filling raw rubber part in the vulcanization technique can be taken as reference, or our technical workers demonstrate it as adjusting.)
3. Please put the down machine frame rightly aiming at the broken part, meanwhile, put the hydraulic pressure plate and the lower heating plate under the broken part.
4. Please put the upper heating plate on the broken part, and lay up the heat insulation plate, and then install the machine frame.
5. Install the screw and screw down.
6. Please connect power with electrical control box by primary cable, and separately connect upper heating plate with electrical control box, and the lower heating plate with electrical control box by secondary cable, meanwhile, please separately connect upper heating plate and electrical control box, lower heating plate and electrical control box with temperature-measure components.
7. Please pay attention to the corresponding electrical control box as connection. Please connect hydraulic plate and pressure-test pump with high pressure tube, and then start the electrical control box, meanwhile, and affuse water to the condition of vulcanizing pressure.Spot Belt Repair Vulcanizer suppliers
website:http://www.arphu-en.com/vulcanizing-equipment/spot-belt-repair-vulcanizer/
Sex: Undisclosed